Yamaha T135S Service Manual Download Page 181 | Manualshive

Page: 181 / 349

background image

YamahaT135.COM

ENG

4-65

CRANKCASE AND CRANKSHAFT

5. Remove:

9

crankcase bolts

NOTE:

Loosen each bolt 1/4 of a turn at a time, in
stages and in a crisscross pattern. After all of
the bolts are fully loosened, remove them.

6. Remove:

9

right crankcase

9

dowel pins

c

C

Tap on one side of the crankcase with a soft-
face hammer. Tap only on reinforced por-
tions of the crankcase, not on the crankcase
mating surfaces. Work slowly and carefully
and make sure the crankcase halves sepa-
rate evenly.

7. Remove:

9

crankshaft assembly

NOTE:

Use the crankcase separating tool.

w

Never use the hammer to tapping and
removing the crankshaft directory.

EAS00394

CHECKING THE CRANKSHAFT AND
CONNECTING ROD

1. Measure:

9

crankshaft runout
Out of specification

→

Replace the crank-

shaft, bearing or both.

NOTE:

Turn the crankshaft slowly.

Maximum crankshaft runout

0.03 mm (0.0012 in)

Crankcase separating tool:

90890-01135

5YP-F8197-E0_4_1 05.6.27 19:33 Page 65

Yamaha T135 Service Manual

YamahaT135.COM

«
...
179
180
181
182
183
...
»

Summary of Contents for T135S






























































































































































































































































































































































Reviews:

No comments

Related manuals for T135S

Brand: yasuni Pages: 8

Brand: AGV Pages: 45

Brand: KTM Pages: 21

TorqDrive Clutch Pack

Brand: Rekluse Pages: 18

Brand: Bajaj Pages: 319

Dirt rocket XM500

Brand: X-TREME scooter Pages: 14

Brand: Yamaha Pages: 400

Brand: hepco & becker Pages: 9

Brand: SW-Motech Pages: 2

HPS.11.258.900-01

Brand: SW-Motech Pages: 2

TRT.00.787.32500/B

Brand: SW-Motech Pages: 6

Brand: MARLINK Pages: 3

CIAK MASTER 50-4T

Brand: Malaguti Pages: 31

Brand: Rockford Fosgate Pages: 8

Brand: Rockford Fosgate Pages: 17

MicroFlooter 8500220

Brand: Wunderlich Pages: 2

Brand: APRILIA Pages: 256

Brand: hepco & becker Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands