Yamaha T135S Service Manual Download Page 334

Page: 334 / 349

YamahaT135.COM

ELEC

COOLING SYSTEM

8-42

4. Radiator fan motor

Disconnect the radiator fan motor coupler
from the wireharness.

Connect the battery (12 V) as shown.

Battery positive lead

→

blue

Battery negative lead

→

black

Does the radiator fan motor turn?

YES

The radiator fan
motor is faulty and
must be replaced.

5. Radiator fan motor relay

Disconnect the radiator fan motor relay cou-
pler.

Connect the pocket tester to the radiator fan
motor relay coupler (relay side) as shown.

Battery positive lead

→

brown

Battery negative lead

→

white/yellow

Positive tester probe

→

brown

Negative tester probe

→

blue

Check the radiator fan motor relay blue and
brown for continuity.

Does the coupler is OK?

YES

Replace the radiator
fan motor relay.

5YP-F8197-E0_8_1 05.6.27 19:28 Page 42

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands