Yamaha T135S Service Manual Download Page 223

Page: 223 / 349

YamahaT135.COM

CARB

CARBURETOR

6-11

EAS00916

CHECKING AND ADJUSTING THE
THROTTLE POSITION SENSOR

NOTE:

Before adjusting the throttle position sensor,
the engine idling speed should be properly
adjusted.

Be sure to adjust the angle when removed the
throttle position sensor.

1. Check:

throttle position sensor

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω ×

1k) to the

terminals of the throttle position sensor.

b. Measure the throttle position sensor resis-

tance.
Out of specification

→

Replace the throttle

position sensor.

L L Y

Maximum throttle position sensor
resistance

3–7 k

Ω

at 20 °C

(blue-black/blue)

Positive (+) pocket tester probe

→

blue terminal

Negative (-) pocket tester probe

→

black/blue terminal

8. Adjust:

throttle cable free play

Refer to “ADJUSTING THE THROTTLE
CABLE FREE PLAY” in chapter 3.

Throttle cable free play (at the
flange of the throttle grip)

3–7 mm (0.12–0.18 in)

7. Adjust:

engine idling speed

Refer to “ADJUSTING THE ENGINE IDLING
SPEED” in chapter 3.

Engine idling speed

1,300–1,500 r/min

5YP-F8197-E0_6 05.6.27 19:31 Page 11

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands