Yamaha T135S Service Manual Download Page 158

Page: 158 / 349

YamahaT135.COM

4-42

ENG

GENERATOR AND STARTER CLUTCH

EAS00355

INSTALLING THE STARTER CLUTCH
(T135SE)

1. Install:

starter clutch

NOTE:

While holding the generator rotor

with the

sheave holder, tighten the starter clutch bolt.

Do not allow the sheave holder to touch the
projection on the generator rotor.

Lock the threads on the starter clutch bolts by
staking them with a center punch.

EAS00353

INSTALLING THE GENERATOR

1. Install:

woodruff key

generator rotor

generator rotor nut

NOTE:

Clean the tapered portion of the crankshaft
and the generator rotor hub.

When installing the generator rotor, make sure
the woodruff key is properly sealed in the key-
way of the crankshaft.

2. Tighten:

generator rotor nut

NOTE:

While holding the generator rotor

with the

sheave holder

, tighten the generator rotor

nut.

Do not allow the sheave holder to touch the
projection on the generator rotor.

Sheave holder

90890-01701

Sheave holder

90890-01701

14 Nm (1.4 m•kg, 10 ft•lb)

70 Nm (7.0 m•kg, 50 ft•lb)

5YP-F8197-E0_4_1 05.6.27 19:32 Page 42

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands