Yamaha T135S Service Manual Download Page 276

Page: 276 / 349

YamahaT135.COM

CHAS

STEERING HEAD

7-46

EAS00679

REMOVING THE LOWER BRACKET

1. Stand the vehicle on a level surface.

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove:

side cowlings (left and right)

center panels

inner panel
Refer to “REMOVING THE FRONT COWL-
INGS” in chapter 3.

front fork
Refer to “FRONT FORK”.

handlebar
Refer to “HANDLEBAR”.

3. Remove:

upper ring nut

lower ring nut

NOTE:

Hold the lower ring nut with the steering nut
wrench, and then remove the upper ring nut with
the ring nut wrench.

Securely support the lower bracket so that
there is no danger of it falling.

EAS00681

CHECKING THE STEERING HEAD

1. Wash:

bearings

bearing races

Steering nut wrench

90890-01403

Ring nut wrench

90890-01268

Recommended cleaning solvent

Kerosene

5YP-F8197-E0_7_1 05.6.27 19:30 Page 46

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands