Yamaha T135S Service Manual Download Page 321

Page: 321 / 349

YamahaT135.COM

ELEC

LIGHTING SYSTEM

8-29

4. The auxiliary light fails to come on.

1. Meter light bulb and socket

Check the meter light bulb and socket for
continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the meter light bulb and socket OK?

YES

Replace the auxil-
iary light bulb,
socket or both.

2. Voltage

Connect the pocket tester (AC 20 V) to the
auxiliary light coupler (wire harness side) as
shown.

Positive tester probe

→

blue

Negative tester probe

→

black

Set the main switch to “ON”.

Start the engine.

Measure the voltage (AC 12 V) of blue lead
terminal

on the auxiliary light coupler

(wire harness side).

Is the voltage within specification?

[L]

[R]

YES

Replace the rectifi-
er/regulator.

This circuit is OK.

5YP-F8197-E0_8_1 05.6.27 19:27 Page 29

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands