Yamaha T135S Service Manual Download Page 326

Page: 326 / 349

YamahaT135.COM

ELEC

8-34

SIGNALING SYSTEM

EAS00797

2. The tail/brake light fails to come on.

1. Tail/brake light bulb and socket

Check the tail/brake light bulb and socket for
continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the tail/brake light bulb and socket OK?

3. Voltage

Connect the pocket tester (DC 20 V) to the
tail/brake light coupler (wire harness side) as
shown.

Positive tester probe

→

green/yellow

Negative tester probe

→

black

Set the main switch to “ON”.

Pull in the brake lever or push down on the
brake pedal.

Measure the voltage (DC 12 V) of green/yel-
low lead terminal

on the tail/brake light

coupler (wire harness side).

Is the voltage within specification?

2. Brake light switches

Check the brake light switches for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the brake light switch OK?

YES

Replace the tail/
brake light bulb,
socket or both.

YES

Replace the brake
light switch.

YES

The wiring circuit
from the main
switch to the
tail/brake light cou-
pler is faulty and
must be repaired.

This circuit is OK.

5YP-F8197-E0_8_1 05.6.27 19:27 Page 34

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands