Yamaha T135S Service Manual Download Page 62

Page: 62 / 349

YamahaT135.COM

CHK

ADJ

ADJUSTING THE VALVE CLEARANCE

3-8

5. Move:

radiator assembly
To swing the radiator assembly toward the
front side.

6. Remove:

water pump assembly

O-rings

7. Remove:

cylinder head cover

gasket

8. Remove:

timing check plug

(with O-ring)

center plug

(with O-ring)

9. Measure:

valve clearance
Out of specification

→

Adjust.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the crankshaft counterclockwise.
b. When the piston is at TDC on the compres-

sion stroke, align the “I” mark

on the

camshaft sprocket with the stationary point-
er

on the cylinder head.

Valve clearance (cold)

Intake valve

0.10–0.14 mm (0.0039–0.0055 in)

Exhaust valve

0.16–0.20 mm (0.0063–0.0079 in)

5YP-F8197-E0_3_1 05.6.27 20:32 Page 8

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands