Yamaha T135S Service Manual Download Page 328

Page: 328 / 349

YamahaT135.COM

ELEC

8-36

SIGNALING SYSTEM

5. Voltage

Connect the pocket tester (DC 20 V) to the
turn signal light coupler (wire harness side)
as shown.

Turn signal light

Rear

∫

Front

Left turn signal light

Positive tester probe

→

chocolate

Negative tester probe

→

ground

Right turn signal light

Positive tester probe

→

dark green

Negative tester probe

→

ground

Turn signal indicator light

Positive tester probe

→

chocolate

Negative tester probe

→

ground

Positive tester probe

→

dark green

Negative tester probe

→

ground

2 1

4. Voltage

Connect the pocket tester (DC 20 V) to the
turn signal relay coupler as shown.

Positive tester probe

→

brown/white

Negative tester probe

→

ground

Set the main switch to “ON”.

Measure the voltage (DC 12 V) on
brown/white lead terminal

at the turn sig-

nal relay coupler.

Is the voltage within specification?

YES

The turn signal relay
is faulty and must be
replaced.

[L]

[R]

5YP-F8197-E0_8_1 05.6.27 19:28 Page 36

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands