Yamaha T135S Service Manual Download Page 88 | Manualshive

Page: 88 / 349

background image

YamahaT135.COM

a

CHK

ADJ

3-34

LUBRICATING THE DRIVE CHAIN/

CHECKING THE BRAKE FLUID LEVEL

EAS00143

LUBRICATING THE DRIVE CHAIN

The drive chain consists of many interacting
parts. If the drive chain is not maintained prop-
erly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
vehicle is used in dusty areas.
Use only kerosene to clean the drive chain.
Wipe the drive chain dry and thoroughly lubri-
cate it with engine oil or chain lubricant that is
suitable for non-O-ring chains.

EAS00115

CHECKING THE BRAKE FLUID LEVEL

1. Stand the vehicle on a level surface.

NOTE:

Make sure the vehicle is upright.

2. Check:

9

brake fluid level
Below the minimum level mark

a

→

Add

the recommended brake fluid to the proper
level.

w

9

9

Use only the designated brake fluid.
Other brake fluids may cause the rubber
seals to deteriorate, causing leakage and
poor brake performance.

9

9

Refill with the same type of brake fluid that
is already in the system. Mixing brake flu-
ids may result in a harmful chemical reac-
tion, leading to poor brake performance.

9

9

When refilling, be careful that water does
not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor lock.

Recommended lubricant

Engine oil or chain lubricant
suitable for non-O-ring chains

Recommended brake fluid

DOT3 or 4

5YP-F8197-E0_3_1 05.6.27 20:32 Page 34

Yamaha T135 Service Manual

YamahaT135.COM

«
...
86
87
88
89
90
...
»

Summary of Contents for T135S






























































































































































































































































































































































Reviews:

No comments

Related manuals for T135S

Brand: Dakota Digital Pages: 6

WARRIOR YFM350XS

Brand: Yamaha Pages: 46

Brand: Memphis Shades Pages: 2

990D0-44G00-ALM

Brand: Suzuki Pages: 24

Brand: Wedze Pages: 63

TXT ROOKIE - 2006

Brand: GAS GAS Pages: 32

Brand: PIAGGIO Pages: 275

Brand: Hudora Pages: 8

Brand: R&G Pages: 2

Brand: BUMOT Pages: 5

Brand: APRILIA Pages: 168

Brand: HYOSUNG Pages: 74

Brand: VOIGT MT Pages: 2

Brand: Orion Pages: 156

Brand: Healtech Pages: 2

Brand: Healtech Pages: 3

Drystash Series

Brand: Oxford Pages: 20

Heritage Series

Brand: Oxford Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands