Yamaha T135S Service Manual Download Page 75

Page: 75 / 349

YamahaT135.COM

CHK

ADJ

3-21

CLEANING THE AIR FILTER ELEMENT/

ADJUSTING THE CLUTCH RELEASE SYSTEM/

CHECKING THE CARBURETOR JOINT AND INTAKE MANIFOLD

6. Install:

center panel (lower)
Refer to “INSTALLING THE CENTER PAN-
ELS”.

EAS00086

ADJUSTING THE CLUTCH RELEASE
SYSTEM

1. Adjust:

clutch release system

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen the locknut

b. Turn the adjusting screw

in completely,

then turn the adjusting screw out the speci-
fied number of turns.

c. Tighten the locknut.

NOTE:

Hold the adjusting screw and tighten the lock-
nut.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Adjusting screw:

1/8 turns out

8 Nm (0.8 m•kg, 6.0 ft•lb)

EAS00094

CHECKING THE CARBURETOR JOINT
AND INTAKE MANIFOLD

1. Remove:

side cowlings (left and right)

center panels (upper and lower)

front cowling

rear cowlings (left and right)

inner panel
Refer to “COVERS”.

2. Check:

carburetor joint

intake manifold

Cracks/damage

→

Replace.

Refer to “CARBURETOR” in chapter 6.

5YP-F8197-E0_3_1 05.6.27 20:32 Page 21

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands