Yamaha T135S Service Manual Download Page 84

Page: 84 / 349

YamahaT135.COM

CHK

ADJ

3-30

ADJUSTING THE REAR BRAKE LIGHT SWITCH/

CHECKING THE FRONT BRAKE HOSE

2. Adjust:

rear brake light operation timing

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Hold the main body

of the rear brake

light switch so that it does not rotate and
turn the adjusting nut

in direction

until the rear brake light comes on at the
proper time.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Direction

Brake light comes on

sooner.

Direction

Brake light comes on

later.

EAS00129

CHECKING THE FRONT BRAKE HOSE

1. Check:

brake hose
Cracks/damage/wear

→

Replace.

2. Check:

brake hose clamp
Loose Connection

→

Tighten the clamp

bolt.

3. Hold the vehicle upright and apply the front

brake several times.

4. Check:

brake hose
Brake fluid leakage

→

Replace the dam-

aged hose.
Refer to “FRONT BRAKE” in chapter 7.

5YP-F8197-E0_3_1 05.6.27 20:32 Page 30

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands