Yamaha T135S Service Manual Download Page 336 | Manualshive

Page: 336 / 349

background image

YamahaT135.COM

ELEC

SELF-DIAGNOSIS

8-44

SELF-DIAGNOSIS

The T135SE/S features a self-diagnosing system for following circuit (-s).

1. Throttle position sensor (TPS)
2. Thermo sensor

1. ENGINE TROUBLE INDICATOR LIGHT

When the main switch is turned to “ON”, the following items are monitored and the condition codes are
displayed on the coolant temperature warning indicator light (irrespective of whether the engine is run-
ning or not).

Item

Condition

Response

Display condition code

9

Enables the vehicle to run so
that the ignition timing is
fixed when the throttle is fully
opened.

9

Displays the condition code
on the coolant temperature
warning indicator light.

9

Enables the vehicle to run so
that the ignition timing is
fixed.

9

Displays the condition code
on the coolant temperature
warning indicator light.

Throttle position sen-
sor (TPS)

Thermo sensor

Disconnected
Short-circuit

Blinks in
Fault code [1]

Blinks in
Fault code [2]

Locked

Disconnected
Short-circuit

Blinks in
Fault code [3]

5YP-F8197-E0_8_1 05.6.27 19:28 Page 44

Yamaha T135 Service Manual

YamahaT135.COM

«
...
334
335
336
337
338
...
»

Summary of Contents for T135S






























































































































































































































































































































































Reviews:

No comments

Related manuals for T135S

Brand: ZARD Pages: 2

Brand: HYOSUNG Pages: 199

Brand: Crivit Pages: 70

Two Fifty 250 cc

Brand: Mash Pages: 62

Brand: Romet Pages: 52

Brand: Hudora Pages: 8

Brand: hepco & becker Pages: 2

Brand: Hermes Pages: 23

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 6

Brand: hepco & becker Pages: 3

400 SUPER COMPETITION 1999

Brand: KTM Pages: 40

HIMALAYAN EURO IV 2017

Brand: Royal Enfield Pages: 294

Brand: Royal Enfield Pages: 90

Brand: Honda Pages: 174

Brand: Sky Team Pages: 40

Brand: GAS GAS Pages: 143

Brand: Yamaha Pages: 744

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands