Yamaha T135S Service Manual Download Page 325

Page: 325 / 349

YamahaT135.COM

ELEC

8-33

4. Voltage

Connect the pocket tester (DC 20 V) to the
horn connector at the pink terminal as
shown.

Positive tester probe

→

pink

Negative tester probe

→

ground

Set the main switch to “ON”.

Measure the voltage (DC 12 V) of pink lead
terminal

at the horn terminal.

Is the voltage within specification?

YES

Replace the horn.

Repair or replace
the horn.

SIGNALING SYSTEM

EAS00796

CHECKING THE SIGNALING SYSTEM

1. The horn fails to sound.

1. Horn switch

Check the horn switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the horn switch OK?

YES

Replace the left han-
dlebar switch.

2. Voltage

Connect the pocket tester (DC 20 V) to the
horn connector at the horn terminal as
shown.

Positive tester probe

→

brown

Negative tester probe

→

ground

Set the main switch to “ON”.

Measure the voltage (DC 12 V) of brown
lead terminal at the horn terminal.

Is the voltage within specification?

YES

The wiring circuit
from the main switch
to the horn connec-
tor is faulty and must
be repaired.

3. Horn

Disconnect the pink connector at the horn
terminal.

Connect a jumper lead

to the horn termi-

nal and ground the jumper lead.

Set the main switch to “ON”.

Does the horn sound?

YES

The horn is OK.

5YP-F8197-E0_8_1 05.6.27 19:27 Page 33

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands