Yamaha T135S Service Manual Download Page 89

Page: 89 / 349

YamahaT135.COM

CHK

ADJ

3-35

CHECKING THE BRAKE FLUID LEVEL/

CHECKING AND ADJUSTING THE STEERING HEAD

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.

NOTE:

In order to ensure a correct reading of the brake
fluid level, make sure the top of the brake fluid
reservoir is horizontal.

EASF0010

CHECKING AND ADJUSTING THE
STEERING HEAD

1. Stand the vehicle on a level surface.

Securely support the vehicle so that there is
no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that the
front wheel is elevated.

2. Check:

steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding/looseness

→

Adjust the steering

head.

3. Remove:

side cowlings (left and right)

front cowling

center panels (upper and lower)

inner panel
Refer to “COVERS”.

5YP-F8197-E0_3_1 05.6.27 20:32 Page 35

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands