Yamaha T135S Service Manual Download Page 304

Page: 304 / 349

YamahaT135.COM

ELEC

8-12

IGNITION SYSTEM

EAS00744

5. Spark plug cap resistance

Remove the spark plug cap from the spark
plug lead.

Connect the pocket tester (“

Ω ×

1k” range) to

the spark plug cap as shown.

Measure the spark plug cap resistance.

Is the spark plug cap OK?

YES

Replace the spark
plug cap.

Spark plug cap resistance

5 k

Ω

at 20°C (68°F)

EAS00742

4. Ignition spark gap

Disconnect the spark plug cap from the
spark plug.

Connect the ignition checker

as shown.

Spark plug cap

Set the main switch to “ON”.

Crank the engine by pushing the start switch
and gradually increase the spark gap until a
misfire occurs.

Measure the ignition spark gap

Is there a spark and is the spark gap within
specification?

YES

The ignition system
is OK.

Minimum ignition spark gap

6 mm (0.24 in)

5YP-F8197-E0_8_1 05.6.27 19:27 Page 12

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands