Yamaha T135S Service Manual Download Page 196

Page: 196 / 349

YamahaT135.COM

ENG

4-80

TRANSMISSION

21.1~21.3 mm

4. Check:

transmission gear engagement
(each pinion gear to its respective wheel
gear)
Incorrect

→

Reassemble the transmission

axle assemblies.

NOTE:

When reassembling the drive axle, press the
2nd wheel gear

onto the drive axle

shown.

5. Check:

transmission gear movement
Rough movement

→

Replace the defective

part(s).

6. Check:

circlips
Bends/damage/looseness

→

Replace.

EAS00426

INSTALLING THE TRANSMISSION

1. Install:

shift fork guide bar

shift fork “R”

shift fork “L”

shift drum

NOTE:

The embossed marks on the shift forks should
face towards the right side of the engine and
be in the following sequence :
“R”, “L”.

Be sure install the side plate into the slot on
the shift drum.

5YP-F8197-E0_4_1 05.6.27 19:33 Page 80

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands