Yamaha T135S Service Manual Download Page 56

Page: 56 / 349

YamahaT135.COM

CHK

ADJ

3-2

PERIODIC MAINTENANCE AND LUBRICATION INTERVALS

EAU18660

NOTE:

The air filter needs more frequent service if you are riding in unusually wet or dusty areas.

Hydraulic brake service

Regularly check and, if necessary, correct the brake fluid level.

Every two years replace the internal components of the brake master cylinder and caliper, and change the brake fluid.

Replace the brake hoses every four years and if cracked or damaged.

Cooling system

Check coolant level and vehicle for coolant leakage.

√

Change the YAMAHA GENUINE COOLANT.

Every 3 years

Front and rear brake
switches

Check operation.

√

Moving parts and ca-
bles

Lubricate.

√

Throttle grip housing
and cable

Check operation and free play.

Adjust the throttle cable free play if necessary.

Lubricate the throttle grip housing and cable.

√

Air induction system

Check the air cut-off valve, reed valve, and hose for dam-
age.

Replace any damaged parts if necessary.

√

Lights, signals and
switches

Check operation.

Adjust headlight beam.

√

NO.

ITEM

CHECK OR MAINTENANCE JOB

ODOMETER READING (

1000 km)

ANNUAL

CHECK

√

5YP-F8197-E0_3_1 05.6.27 20:32 Page 2

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands