W6 N 707D free-arm Manual Download Page 3

Page: 3 / 91

Manual • Cover W6 N 707D Free Arm • 29/10/2019 • 1.0 • GBR

Contents

Safety notes ............................................................................................................ 5

1.1

Notes on operational safety ............................................................................................ 5

1.2

Instructions for use .......................................................................................................... 6

1.3

After sewing .................................................................................................................... 7

1.4

Tips for a long service life ............................................................................................... 7

1.5

What we expect from you ............................................................................................... 8

Assembling your cover .......................................................................................... 9

2.1

Unpacking ....................................................................................................................... 9

2.2

Setting up ......................................................................................................................10

2.3

Assembling your cover..................................................................................................10

2.4

Unplugging the power plug ...........................................................................................14

Getting to know your cover ................................................................................. 15

3.1

Front view .....................................................................................................................15

3.2

Side view .......................................................................................................................16

3.3

Electrical connections ...................................................................................................17

3.4

View of the hook area (most important parts) ...............................................................18

3.5

Why using W6 thread and needles is important ...........................................................18

Standard accessories .......................................................................................... 19

Operating elements .............................................................................................. 20

5.1

On and off switch ..........................................................................................................20

5.2

Jack for the power supply and foot controller ...............................................................21

5.3

Power plug ....................................................................................................................21

5.4

Foot controller ...............................................................................................................22

5.5

Extension table .............................................................................................................22

5.6

Opening and closing the front cover hook flap .............................................................23

5.6.1

Opening the front cover hook flap ....................................................................23

5.6.2

Closing the front cover hook flap .....................................................................23

5.7

Presser foot pressure dial .............................................................................................24

5.8

4 thread tension dials ....................................................................................................24

5.9

Stitch length dial ............................................................................................................25

5.10

Lifting and lowering the presser foot lifter .....................................................................25

5.11

Adjusting the seam width ..............................................................................................26

5.11.1

Setting the seam width by removing needles ..................................................26

5.12

Setting the differential feed dial ..................................................................................27

5.13

Hand wheel ................................................................................................................28

Changing the presser foot ................................................................................... 29

6.1 Changing the presser foot ............................................................................................29

6.2 Attaching the extension table ........................................................................................32

Summary of Contents for N 707D free-arm




























































































Search results

Summary of Contents for N 707D free-arm

Reviews:

Related manuals for N 707D free-arm

Brands by name

Popular brands

W6 N 707D free-arm, Manual

Search results

Summary of Contents for N 707D free-arm

Reviews:

Related manuals for N 707D free-arm

Brands by name

Popular brands