background image

Configuration File Parameter Guide

369

Back to Contents

ET685 Administrator and Provisioning Manual

Default:

30

Setting:

tcp_keepintvl

Description:

The time (in seconds) between individual keepalive probes.

Values:

integer

Default:

20

Setting:

tcp_listen

Description:

By default the phone doesn't listen on the network ID port for TCP 
connections (setting: network_id_port). To change this behaviour, enable 
this option.

Values:

on, off

Default:

off

Setting:

terminate_ongoing_calls_on_user_deactivation

Description:

When set to true, will cancel all ongoing calls when the associated identity 
is deactivated via user_active. First the deregistration is done and 
afterwards the calls are canceled.

Values:

on, off

Default:

off

Setting:

terminate_subscribers_on_reboot

Description:

SYSTEM INTERNAL

The default setting causes the phone to un- subscribe (SUBSCRIBE & 
Expire:0) from all open dialog state subscriptions established on function 
keys (key type "extension" or "destination") before rebooting the phone. 
However in some environments it might be desired to keep all existing 
dialog state subscriptions untouched in case of rebooting. In order to do 
so, please turn this setting <OFF> via mass deployment.

Values:

on, off

Default:

on

Summary of Contents for ET685









































































































































































































































































































































































































































Reviews: