manualshive.com logo in svg

VTech ET685, Administrator And Provisioning Manual

Share
Download
VTech ET685 Administrator And Provisioning Manual Download Page 187

Configuration File Parameter Guide

187

Back to Contents

ET685 Administrator and Provisioning Manual

Description:

In case the specific action has taken place (here an outgoing call has 
been started to dial out), a web GET to the specified URL is performed.

Values:

HTTP URL

Default:

blank

Setting:

action_received_attended_transfer

Description:

This event is intended to be used on phone C in a typical attended 
transfer scenario where phone A calls phone B and phone B transfers to 
C. B sends a SIP REFER message to A which causes phone A to send a 
SIP INVITE message to phone C. In this case, a web GET to the specified 
URL is performed.
Note: This event may also be triggered by another RE-INVITE during an 
existing Connection Dialog.

Values:

HTTP URL

Default:

blank

Setting:

action_received_subscr_notify_url

Description:

In case a notify for a subscription was received, http GET requests to the 
specified URL's are performed. When notifies with exact same content 
are received, only the first one will cause the action to be fired to minimize 
the workload for the phone.

Values:

HTTP URL or XML sub trees 

Default:

blank

Setting:

action_redirection_off_url

Description:

In case the specific action has taken place (here CFWD OFF / redirection 
always has been deactivated), a web GET to the specified URL is 
performed.

Values:

HTTP URL

Default:

blank

Setting:

action_redirection_on_url

Description:

In case the specific action has taken place (here CFWD ON / redirection 
always has been activated), a web GET to the specified URL is 
performed.

Summary of Contents for ET685









































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands