Vatech A9 PHT-30CSS Technical Manual Download Page 98

Page: 98 / 244

Page

244

6. Click the

V Vol

button.

Y axis - reference range: 130 ~ 135

130 or less: Reassemble the bite block in the opposite direction of the

column (5 voxel value increase per cell)

135 or more: Reassemble the bite block in the direction of the column (5

voxel value decrease per cell)

X axis - reference range: 220 ~ 230

- 220 or less: move to the left based on the column

- Over 230: Move to the right based on the column

Angle setting

When moving to the right, Start angle: 0 ~ 10

When moving to the left, Start angle: 350 ~ 359

When the start angle is found, it is applied to the following folders.

C:\VCaptureSW\Acquisition\CBCT\WidePANO\REC\reconstruction.vxm

Change the value of the STARTANGLE parameter in the reconstruction.vxm

file

1mm per division

(5 voxel)

Summary of Contents for A9 PHT-30CSS





















































































































































































































































Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands

Vatech A9 PHT-30CSS, Technical Manual

Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands