Vatech A9 PHT-30CSS Technical Manual Download Page 211

Page: 211 / 244

Page

210

244

5: Scan CEPH (Table Control)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~ceph sensor start position offset~~~

1700=>(spm_UATT_xxxx)CEPH_TABLE_A_START_OFFSET_COUNT (0165 = 16.5cm).

0300=>(spm_UBTT_xxxx)CEPH_TABLE_B_START_OFFSET_COUNT (0165 = 16.5cm).

1700=>(spm_UCTT_xxxx)CEPH_TABLE_C_START_OFFSET_COU

NT (0165 = 16.5cm).

0350=>(spm_UDTT_xxxx)CEPH_TABLE_D_START_OFFSET_COUNT (0165 = 16.5cm).

1700=>(spm_UETT_xxxx)CEPH_TABLE_E_START_OFFSET_COUNT (0165 = 16.5cm).

0350=>(spm_UFTT_xxxx)CEPH_TABLE_F_START_OFFSET_COUNT (0165 = 16.5cm).

1700=>(spm_UGTT_xxxx)CEPH_

TABLE_G_START_OFFSET_COUNT (0165 = 16.5cm).

0350=>(spm_UHTT_xxxx)CEPH_TABLE_H_START_OFFSET_COUNT

(0165

16.5cm).0313(HZ)=>(spm_CFRQ_xxxx)CEPH PULSE HZ SET

1790=>(spm_XRFA_xxxx)CEPH_REF_X1_START POSITION (1730 = 17.3cm)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Collimator type

0002=>(spm_COTY_xxxx)COLLIMATOR TYPE SET (0: No collimator)(1: Using 4axis collimator)(2:

Using 1axis collimator)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~

10200=>(spm_COVS_xxxxx)1axis

COL_OFFSET_VAL(1xxxx=> "

-val" (1 = 0.01016mm)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~



1-axis collimator position by exposure mode

11395=>(spm_CBST_xxxxx)COL_PANO_CHILD_VAL (1axis collimator) (00001 = 1pulse)

912 is default by machanical data

03685=>(spm_CCST_xxxxx)COL_PANO_VAL (1axis collimator) (00001 =

1pulse)

3450 is default by machanical data

06660=>(spm_CFST_xxxxx)COL_CT_VAL (1axis collimator) (00001 = 1pulse)

6350 is default by machanical data

09150=>(spm_CGST_xxxxx)COL_CEPH_VAL (1axis collimator) (00001 = 1pulse)

8899 is default by machanical data
1

1969=>(spm_CDST_xxxxx)COL_FILTER_VAL (1axis collimator) (00001 = 1pulse)

11969 is default by machanical data
~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Sensor and collimator drive ratio

122=>(SPM_PSCR) pano_sm_cm_ratio

~~~~~~~~~~~~~~~~~~~~~~~~~~~~

R axis motor torque setting

0025 =>(SPM_RMRT_0001) R_M_RUN_TORQUE

0005 =>(SPM_RMST_0001) R_M_STOP_TORQUE

~~~~~~~~~~~~~~~~~~~~~~~~~~~~

PANO,CT sensor mortor, Collimator motor, CEPH sensor motor torque setting - GMRT, GMST

disabled (3D camera)

2000 =>(SPM_LMRT_0001) LASER_M_RU

N_TORQUE

0050 =>(SPM_LMST_0001) LASER_M_STOP_TORQUE

2500 =>(SPM_TSRT_0001) TEMPLE_M_RUN_TORQUE

0200 =>(SPM_TSST_0001) TEMPLE_M_STOP_TORQUE

20000 =>(SPM_GMRT_0001) G_M_RUN_TORQUE

01000 =>(SPM_GMST_0001) G_M_STOP_TORQUE

Summary of Contents for A9 PHT-30CSS





















































































































































































































































Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands

Vatech A9 PHT-30CSS, Technical Manual

Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands