Vatech A9 PHT-30CSS Technical Manual Download Page 154

Page: 154 / 244

Page

153

244

4.7.

Vertical Laser Beam Alignment

1. Run the Console Software.

2. Click the

Confirm

button and attach the ball phantom with a laser beam jig.

3. Click the laser beam mode to check whether the vertical beam is located at the reference

line of the ball phantom.

4. If the position is not correct, loosen the assembly point with an M4 wrench and move it

left/right so that it comes to the reference line.

5. If the angle of the vertical laser beam is not correct, loosen it with an M3 wrench as shown in

green in the picture below and adjust the angle.

Summary of Contents for A9 PHT-30CSS





















































































































































































































































Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands

Vatech A9 PHT-30CSS, Technical Manual

Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands