Vatech A9 PHT-30CSS Technical Manual Download Page 155

Page: 155 / 244

Page

154

244

Chapter 5.

PANO Image Evaluation

5.1.

Line Pair Resolution evaluation

5.1.1.

Resolution standards

Parameter

LSL (Lower Specification Limit)

USL (Upper Specification Limit)

Lp/mm

3.1

5.1.2.

Phantom Specification

QUART Phantom

QUART - Ball Phantom 2.0

5.1.3.

Test Method

1. Attach the

ball phantom 2.0

and

quart phantom

to the chinrest.

2. Run the Console Software and click the PANO button to go into PANO mode.

3. Choose HD Mode/MAN/Normal mode/exposure condition 70 kVp, 7 mA as the image option

and click the Confirm button.

4. Attach 1 .8 mm Copper Filter on X-Ray Tube.

5. Click the READY button, and acquire/save the image according to the Console Software

guidance.

6. Open the 2D Viewer and save the image.

7. Ensure that the lines can be seen clearly at 3.1 lp/mm.

5.1.4.

Test Result

Parameter

LSL

Measurement value

USL

Pass/Fail

Lp/mm

3.1

Summary of Contents for A9 PHT-30CSS





















































































































































































































































Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands

Vatech A9 PHT-30CSS, Technical Manual

Search results

Summary of Contents for A9 PHT-30CSS

Reviews:

Related manuals for A9 PHT-30CSS

Brands by name

Popular brands