Ulvac CRYO-U Series Instruction Manual Download Page 66

Page: 66 / 106

Disconnection and Storage

7-2

ULVAC CRYOGENICS INCORPORATED

Loosen the union nut using two spanners and disconnect the flexible

hose by hand.

Figure 7-1 Disconnecting Flexible Hose

7.2 Storage

Do not expose the cryopump to atmosphere for a long time. It may adsorb moisture in the

atmosphere and result in performance degradation.

Loosen the nut

with a spanner.

Hold with a

spanner.

CAUTION

◆

If the cryopump is stored in the state attached to your vacuum system, the cryopump

should be kept in a vacuum (of 100Pa or less) or under the atmospheric pressure

replaced with dry nitrogen.

◆

If the cryopump is removed from your vacuum system,

1. After the cryopump has reached room temperature completely, disconnect the

flexible hoses.

Summary of Contents for CRYO-U Series











































































































Search results

Summary of Contents for CRYO-U Series

Reviews:

Related manuals for CRYO-U Series

Brands by name

Popular brands

Ulvac CRYO-U Series, Instruction Manual

Search results

Summary of Contents for CRYO-U Series

Reviews:

Related manuals for CRYO-U Series

Brands by name

Popular brands