manualshive.com logo in svg

Trilithic Two, Operation Manual

Share
Download
Trilithic Two Operation Manual Download Page 58

Model Two & Model Two Lite - Operation Manual

58

The Model Two displays the transmission measurement. The reference level indicates 

Δ

 dB to

show the difference between the current Scan Level and the Zero Reference scan. In the example
above, a 6 dB loss is seen with the transmission measurement.

The new Zero Reference remains in the Model Two’s nonvolatile memory even when the Model
Two is turned off. This enables you to measure the level’s relative change at a later time. To
perform a new Transmission Test at any time, confirm that TRANSMISSION is set to ON in the
Measurement Setup menu and then press 

SPECT

. The Model Two performs a Spectrum Scan

and compares it to the reference data.

Press 

UP

 or 

DOWN

 to move the marker frequency.

You may wish to stop the scanning process so you can study the transmission graph. Simply press

F1 

(HOLD). The scan marker stops moving. To resume scanning, press 

F1 

(TRIG).

As in Spectrum mode (absolute), other functions are available by using the 

F3

 key to change the

function of softkeys 

F1

 and 

F2

.

Press 

F3

 to change the function of softkeys 

F1

 and 

F2 

to Scale and Ref.

Change the display scale by pressing softkey 

F1

 (SCALE). Change the reference level by

pressing softkey 

F2

 (REF) and using the 

UP

 and 

DOWN

 arrow keys to change the reference.

Note:

 Channels in the Base Channel Plan that are not active on your

system have a transmission indication near 0 dB, because there was no
signal to be changed. A User Plan can be configured with only active
channels by deleting the unused channels (See 

Edit User Plan 

on Page

33.) This provides a transmission scan with all active data.

Note:

 The Span function does 

NOT

 operate when the Model Two is in

the TRANSMISSION mode. For normal (absolute value) Spectrum
Measurements, set the TRANSMISSION selection to OFF.

Summary of Contents for Two





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands