TLV SC-F71, Instruction Manual

Page: 86 / 390

172-65710M-04 (SC-F71 Parameters/Functions) 23 Dec 2021
85
Engineering
Mode
Function
block No. 31 Retransmission output 1 scale high
AHS1
Input 1_Measured value
(PV), Input 1_Local SV,
Input 1_SV monitor
value, and Remote
setting input value:
Input 1_Input range high
(Control with PV select:
PV select input range
high)
Input 1_Deviation:

(Input 1_Input span)
Measured value (PV) of
differential temperature
input: 100
4
Retransmission output 1 scale low
A L S 1
Input 1_Measured value
(PV), Input 1_Local SV,
Input 1_SV monitor
value, and Remote
setting input value:
Input 1_Input range low
(Control with PV select:
PV select input range low)
Input 1_Deviation:

(Input 1_Input span)
Measured value (PV) of
differential temperature
input: -100
4
Function
block No. 32 Retransmission output 2 scale high
A H S 2
Same as Retransmission
output 1 scale high 4
Retransmission output 2 scale low
A L S 2
Same as Retransmission
output 1 scale low 4
Function
block No. 33 Retransmission output 3 scale high
A H S 3
Same as Retransmission
output 1 scale high 4
Retransmission output 3 scale low
A L S 3
Same as Retransmission
output 1 scale low 4
Function
block No. 41 Event 1 differential gap
E H 1
TC/RTD inputs: 2
V/I inputs: 0.2% of input
span
MV: 0.2 3
Function
block No. 42 Event 2 differential gap
E H 2
3
Function
block No. 43 Event 3 differential gap
E H 3
3
Function
block No. 44 Event 4 differential gap
E H 4
3
Function
block No. 51 Input 1_Start determination point
1. P d A
0

Input 1_Level PID differential gap
1. L H S
TC/RTD inputs: 2
V/I inputs: 0.2

Function
block No. 58 Cascade_AT mode (master-side)
M A S.A T
TC/RTD inputs: 0
V/I inputs: 1

Cascade_AT mode (slave-side)
S L V.A T

Input circuit error alarm set value
I C A
TC/RTD inputs: 10
V/I inputs: 5% of Input
1_Input span

Function
block No. 71 Input 1_Setting limiter high
1. S L H
Input 1_Input range high
(Control with PV select:
PV select input range
high)

Input 1_Setting limiter low
1. S L L
Input 1_Input range low
(Control with PV select:
PV select input range low)

1)
When Input 1_Input type is changed.
2)
When Input 1_Display unit is changed.
Condition
1. When "Remote setting input" is selected in "Select function for Input 2" AND either Voltage input or Current input
are selected in "Input 2_Input type".
2. When "Remote setting input" is selected in "Select function for Input 2" AND either Voltage input or Current input
are selected in "Input 2_Input type", OR "Control with PV select is selected in "Select function for Input 2".
3. The condition is either of the following.
・
"Manipulated output value" is not selected in "Event type" AND "Control with PV select" is selected in "Select
function for Input 2".
・
Event type is a setting other than Manipulated output value AND Event assignment is either "Input 1" or "Differential
temperature input."
4. Retransmission output is "No retransmission output," "Input 1_Measured value (PV)," "Input 1_Set value (SV)," "Input
1_Deviation," "Input 1_Remote setting input value," OR Measured value (PV) of differential temperature input.
4.1.3 When Input 1_Decimal point position (
1.PGDP
) is changed [Engineering