TLV SC-F71, Instruction Manual

Page: 74 / 390

172-65710M-04 (SC-F71 Parameters/Functions) 23 Dec 2021
73
285
1. oLb
Input 1_Lower range of
corrective action amount
4)
0.0 to 105.0% 20.0
286
1. oHb
Input 1_Upper range of
corrective action amount
4)
0.0 to 105.0% 20.0
1)
Displayed when 3 to 9 is selected in "Input 1_Control action".
2)
Displayed when "7 (Pressure control operation [MC-VCOS(R)])" is selected.
3)
Displayed when "9 (Temperature control operation [MC-VCOS(R)])" is selected, AND "Current" or "Voltage input" is selected in Input
1_type.
4)
Displayed when "3-7 (Pressure control operation [MC-(V)COS(R)])" is selected in "Input 1_Control action".
5)
Displayed when "1" is selected in "Input 1_Response speed self-learning selection".
3.9.19 Function block No. 54: Input 2_Valve factor (
2.McVc
)
No. Symbol
Name Data range
Factory
set value
User
set value

Fn54
Function block No. 54
1)
This is the first parameter symbol of
Function block No. 54
 
287
2. A
Input 2_Valve coefficient A
1)
-1999 to 9999 0
288
2. b
Input 2_Valve coefficient b
1)
-1999 to 9999 0
289
2. C
Input 2_Valve coefficient C
1)
-1999 to 9999 0
290
2. d
Input 2_Valve coefficient d
1)
-1999 to 9999 0
291
2. E
Input 2_Valve coefficient E
1)
-1999 to 9999 0
292
2. F
Input 2_Valve coefficient F
1)
When Input 2_Control action is set to 3 to
6 or 8:
0: kg/cm
2
G
1: barg
2: psig
3: kPaG
4: MPaG
When Input 2_Control action is 7 or 9:
10: mmHg/Torr
11: mbar
12: inHg
13: psi
14: kPa
NOTE: The pressure unit to be entered for
the pressure value is defined by the valve
coefficient F. Parameters to be entered in
pressure units, such as measurement
input range, target set value, and alarm
set value, must be entered in the same
pressure units defined by the valve
coefficient F. If the pressure unit and the
parameter do not match, the product will
not operate properly.. To use a pressure
unit other than the valve coefficient F
(indicated on the valve coefficient plate),
refer to the "Converting valve coefficient"
section in "8.8 Using with MC-COS/MC-
VCOS" in the instruction manual
(parameters/functions) to convert the
valve coefficient and change the valve
coefficient F along with valve coefficients
A, C, and E.
Same as
Input 1_
Valve
coefficient F
(pressure
unit)
293
2. GSL
Input 2_Pressure
standard for valve
coefficient F
2)
0: Atmospheric pressure standard
1: Absolute pressure standard Same as
pressure
standard for
Input 1_
Valve
coefficient F
294
2. VSL
Input 2_Control valve
selection
2)
0: MC-VCOS(R)
1: PC-VCOS(R) 0
295
2. PrL
Input 2_Pressure (Temp)
limiter
1)
When Input 2_Control action is set to 3 to
7:
Input 2_Input range low to Input 2_Input
range high
When Input 2_Control action is set to 8: When a
setting other
than
“7” is
selected in
Input 2_