Talkswitch 48-CA/CVA User Manual Download Page 221 | Manualshive

Page: 221 / 243

background image

A P P E N D I X G 2 0 9

TalkSwitch copyright © 2006 — All Rights reserved.
TalkSwitch is a division of Centrepoint Technologies Inc.

TalkSwitch software is protected under copyright law and international
treaties. Unauthorized reproduction or distribution of TalkSwitch software,
or any portion of it, in any form, may result in severe civil and criminal
penalties, and will be prosecuted to the maximum extent of the law.

TalkSwitch phone systems use the Appello® SIP stack for VoIP
communications. The Appello® SIP stack was developed by TalkSwitch — a
division of Centrepoint Technologies Inc.

TalkSwitch and Appello are registered trademarks of Centrepoint
Technologies Inc.

Elements of TalkSwitch software are protected under additional copyrights
listed below, and subject to the terms and disclaimers listed below.

A) Copyright © 1998 by the Massachusetts Institute of Technology.

Permission to use, copy, modify, and distribute this software and its
documentation for any purpose and without fee is hereby granted, provided
that the above copyright notice appear in all copies and that both that
copyright notice and this permission notice appear in supporting
documentation, and that the name of MIT not be used in advertising or
publicity pertaining to distribution of the software without specific, written
prior permission. MIT makes no representations about the suitability of this
software for any purpose. It is provided “as is” without express or implied
warranty.

B) Copyright © 2000-2003 Intel Corporation. All rights reserved.

Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:

A P P E N D I X G

A P P E N D I X G : CO P Y R I G H T A N D L I C E N S I NG N O T I CES

CO P Y R I G H T A N D L I CE N S I NG
N O T I CE S

«
...
219
220
221
222
223
...
»

Summary of Contents for 48-CA/CVA




















































































































































































































































Reviews:

No comments

Related manuals for 48-CA/CVA

Brand: A-Link Pages: 6

Brand: M86 Security Pages: 309

Brand: axing Pages: 52

Media Board D/120JCT-LS-EW

Brand: Dialogic Pages: 2

ConnectX-3 Pro MCX349A-XCCN

Brand: Mellanox Technologies Pages: 35

InnoMedia MTA 3328-2R

Brand: VoiceLine Pages: 18

Brand: Accton Technology Pages: 78

Brand: Acromag Pages: 35

Brand: Aaeon Pages: 119

High-Precision AD/DA Board

Brand: Waveshare Pages: 8

Brand: Airlink101 Pages: 64

Brand: ETAS Pages: 29

Brand: Renesas Pages: 4

Brand: H3C Pages: 34

Brand: Primera Pages: 82

Brand: Thecus Pages: 148

Passport 8608GTE

Brand: Nortel Pages: 10

Brand: Williams Sound Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands