Suzuki SFV650 Service Manual Download Page 459

Page: 459 / 573

Front Brakes: 4B-6

Front Brake Caliper Parts Inspection

B944H14206006

Refer to “Front Brake Caliper Disassembly and
Assembly (Page 4B-4)”.

Brake Caliper Cylinder

Inspect the brake caliper cylinder wall for nicks,
scratches or other damage. If any damage is found,
replace the caliper with a new one.

Brake Caliper Piston

Inspect the brake caliper piston surface for any
scratches or other damage. If any damage is found,
replace the piston with a new one.

Brake Caliper Holder Sliding Pin

Inspect the brake caliper holder sliding pins for wear and
other damage. If any damage is found, replace the brake
caliper holder with a new one.

Brake Pad Spring and Pad Guide

Inspect the brake pad spring and pad guide for damage
and excessive bend. If any defects are found, replace
them with new ones.

Rubber Boot

Inspect the rubber boots for damage. If any damages
are found, replace them with the new ones.

Front Brake Disc Removal and Installation

B944H14206007

Removal

1) Remove the front wheel assembly. Refer to “Front

Wheel Assembly Removal and Installation in Section
2D (Page 2D-4)”.

2) Remove the front brake disc (1) by removing its bolts

(2).

I944H1420019-01

I944H1420020-01

I944H1420021-01

I944H1420022-01

I944H1420023-01

I944H1420024-03

Summary of Contents for SFV650






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SFV650

Reviews:

Related manuals for SFV650

Brands by name

Popular brands

Suzuki SFV650, Service Manual

Search results

Summary of Contents for SFV650

Reviews:

Related manuals for SFV650

Brands by name

Popular brands