Suzuki SFV650 Service Manual Download Page 214 | Manualshive

Page: 214 / 573

background image

1D-25 Engine Mechanical:

• Adjust the drive chain slack. Refer to “Drive Chain

Inspection and Adjustment in Section 0B (Page 0B-
15)”.

• After remounting the engine, route the wiring harness

properly. Refer to “Wiring Harness Routing Diagram in
Section 9A (Page 9A-5)”.

• Connect the clutch cable. Refer to “Clutch Cable

Removal and Installation in Section 5C (Page 5C-2)”.

• Install the throttle body. Refer to “Throttle Body

Removal and Installation (Page 1D-10)”.

• Install the front exhaust pipe, exhaust assembly and

muffler. Refer to “Exhaust Pipe / Muffler Removal and
Installation in Section 1K (Page 1K-3)”.

• Install the radiator. Refer to “Radiator / Cooling Fan

Motor Removal and Installation in Section 1F
(Page 1F-5)”.

• Install the air cleaner box. Refer to “Air Cleaner Box

Removal and Installation (Page 1D-6)”.

• Pour engine coolant and engine oil. Refer to “Cooling

System Inspection in Section 0B (Page 0B-12)” and
“Engine Oil and Filter Replacement in Section 0B
(Page 0B-10)”.

• After finishing the engine installation, check the

following items.
– Throttle cable play

Refer to “Throttle Cable Play Inspection and
Adjustment in Section 0B (Page 0B-12)”.

– Throttle valve synchronization

Refer to “Throttle Valve Synchronization in Section
0B (Page 0B-12)”.

– Engine oil and coolant leakage

Refer to “Cooling Circuit Inspection in Section 1F
(Page 1F-4)”.

– Clutch cable play

Refer to “Clutch System Inspection in Section 0B
(Page 0B-14)”.

Engine Top Side Disassembly

B944H11406006

It is unnecessary to remove the engine assembly from
the frame when servicing the engine top side.

NOTE
Before servicing the engine top side with
engine in place, remove the air cleaner box,
throttle body, fuel tank, exhaust pipe, muffler
and etc. Refer to “Engine Assembly Removal
(Page 1D-18)”.

CAUTION

!

Identify the position of each removed part.
Organize the parts in their respective groups
(e.g., intake, exhaust) so that they can be
reinstalled in their original positions.

Radiator Hose / Breather Hose

1) Remove the radiator hose (1), oil cooler hoses (2)

and breather hose (3).

Thermostat

Remove the thermostat assembly (1) and water hoses
(2).

1

2

2

3

I944H1140134-01

1

2

2

I944H1140135-01

«
...
212
213
214
215
216
...
»

Summary of Contents for SFV650






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SFV650

Brand: probrake Pages: 2

Brand: Yamaha Pages: 88

Brand: Crivit Pages: 70

2016 Empulse TT

Brand: Victory Motorcycles Pages: 138

Brand: Crivit Pages: 30

MULTISTRADA 1200S

Brand: Ducati Pages: 311

Brand: Cycle Protect Pages: 15

Brand: Denali Pages: 2

Brand: Honda Pages: 127

Brand: Miller Pages: 22

Brand: Yamaha Pages: 287

Brand: Yamaha Pages: 109

Brand: hepco & becker Pages: 3

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 5

Brand: R&G Pages: 11

Brand: R&G Pages: 14

Brand: Menuett Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands