manualshive.com logo in svg

Suzuki SFV650, Service Manual

The Suzuki SFV650 Service Manual is a comprehensive guide for owners looking to maintain or repair their motorcycle. This manual is available for free download on manualshive.com, providing users with detailed instructions and diagrams to ensure their SFV650 stays running smoothly for years to come.

Share
Download
background image

9B-14 Lighting Systems: 

4) After finishing the hazard switch inspection, reinstall 

the removed parts.

Turn Signal Switch Inspection

B944H19206021

Inspect the turn signal switch in the following 
procedures:

1) Remove the left frame body cover. Refer to “Exterior 

Parts Removal and Installation in Section 9D 
(Page 9D-4)”.

2) Disconnect the left handlebar switch coupler (1).

3) Inspect the turn signal switch for continuity with a 

tester. If any abnormality is found, replace the left 
handlebar switch assembly with a new one.
Refer to “Handlebars Removal and Installation in 
Section 6B (Page 6B-3)”.

Special tool

:  09900–25008 (Multi-circuit tester set)

Tester knob indication
Continuity (

)

4) After finishing the turn signal switch inspection, 

reinstall the removed parts.

Passing Light Switch Inspection

B944H19206022

Inspect the passing light switch in the following 
procedures:

1) Remove the left frame body cover. Refer to “Exterior 

Parts Removal and Installation in Section 9D 
(Page 9D-4)”.

2) Disconnect the left handlebar switch coupler (1).

3) Inspect the passing light switch for continuity with a 

tester.
If any abnormality is found, replace the left 
handlebar switch assembly with a new one.
Refer to “Handlebars Removal and Installation in 
Section 6B (Page 6B-3)”.

Special tool

:  09900–25008 (Multi-circuit tester set)

Tester knob indication
Continuity (

)

4) After finishing the passing light switch inspection, 

reinstall the removed parts.

1

I944H1920036-03

L

PUSH

R

Lg

Lbl

B

Color

Position

I944H1920039-01

1

I944H1920036-03

PUSH

Position

Color

O                                    Y

I944H1920041-01

Summary of Contents for SFV650






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SFV650

KTM Freeride E-XC 2019 Setup Instructions preview
Freeride E-XC 2019
Brand: KTM Pages: 44
Suzuki GSX 11OOF Service Manual preview
GSX 11OOF
Brand: Suzuki Pages: 230
Triumph Daytona Moto2 765 2020 Owner'S Handbook Manual preview
Daytona Moto2 765 2020
Brand: Triumph Pages: 163
LAZER Mambo Evo PURE CARBON User Manual preview
Mambo Evo PURE CARBON
Brand: LAZER Pages: 13
R&G SS0059 Fitting Instructions Manual preview
SS0059
Brand: R&G Pages: 6
Bajaj Discover 100M Service Station Manual preview
Discover 100M
Brand: Bajaj Pages: 319
BMW S 1000XR 2018 Rider'S Manual preview
S 1000XR 2018
Brand: BMW Pages: 241
GAS GAS 2007 PAMPERA 125 Manual preview
2007 PAMPERA 125
Brand: GAS GAS Pages: 58
digades dguard Installation Manual preview
dguard
Brand: digades Pages: 10
O'Neal Dirt Manual preview
Dirt
Brand: O'Neal Pages: 28
Petzl A073AA00 Technical Notice preview
A073AA00
Brand: Petzl Pages: 12
TSG WINTER HELMET User Manual preview
WINTER HELMET
Brand: TSG Pages: 60
KTM 2010 1190 RC8 Owner'S Manual preview
2010 1190 RC8
Brand: KTM Pages: 258
Royal Enfield Classic 350 BS IV Owner'S Manual preview
Classic 350 BS IV
Brand: Royal Enfield Pages: 108
Mahindra Centuro Owner'S Manual preview
Centuro
Brand: Mahindra Pages: 91
HealTech Electronics GIPRO X-TYPE Supplementary Manual preview
GIPRO X-TYPE
Brand: HealTech Electronics Pages: 3
R&G YTI0012BK Fitting Instructions Manual preview
YTI0012BK
Brand: R&G Pages: 6
3M L-905 Reassembly preview
L-905
Brand: 3M Pages: 6

Brands by name

Popular brands

Load more brands