manualshive.com logo in svg

Suzuki SFV650, Service Manual

The Suzuki SFV650 Service Manual is a comprehensive guide for owners looking to maintain or repair their motorcycle. This manual is available for free download on manualshive.com, providing users with detailed instructions and diagrams to ensure their SFV650 stays running smoothly for years to come.

Share
Download
background image

1G-4 Fuel System: 

Diagnostic Information and Procedures

Fuel System Diagnosis

B944H11704001

Condition

Possible cause

Correction / Reference Item

Engine will not start or is 
hard to start (No fuel 
reaching the intake 
manifold)

Clogged fuel filter or fuel hose.

Clean or replace.

Defective fuel pump.

Replace.

Defective fuel pressure regulator.

Replace.

Defective fuel injectors.

Replace.

Defective fuel pump relay.

Replace.

Defective ECM.

Replace.

Open-circuited wiring connections.

Check and repair.

Engine will not start or is 
hard to start (Incorrect 
fuel/air mixture)

TP sensor out of adjustment.

Adjust.

Defective fuel pump.

Replace.

Defective fuel pressure regulator.

Replace.

Defective TP sensor.

Replace.

Defective CKP sensor.

Replace.

Defective IAP sensor.

Replace.

Defective ECM.

Replace.

Defective ECT sensor.

Replace.

Defective IAT sensors.

Replace.

Dirty throttle body.

Clean.

Defective ISC valve.

Replace the STVA.

Engine stalls often 
(Incorrect fuel/air mixture)

Defective IAP sensor or circuit.

Repair or replace.

Clogged fuel filter.

Clean or replace.

Defective fuel pump.

Replace.

Defective fuel pressure regulator.

Replace.

Damaged or cracked vacuum hose.

Replace.

Defective ECT sensor.

Replace.

Defective thermostat.

Replace.

Defective IAT sensor.

Replace.

Defective ISC valve.

Replace the STVA.

Engine stalls often (Fuel 
injector improperly 
operating)

Defective fuel injectors.

Replace.

No injection signal from ECM.

Repair or replace.

Open or short circuited wiring 
connection.

Repair or replace.

Defective battery or low battery voltage.

Replace or recharge.

Engine runs poorly in 
high speed range 
(Defective control circuit 
or sensor)

Low fuel pressure.

Repair or replace.

Defective TP sensor.

Replace.

Defective IAT sensor.

Replace.

Defective IAP sensor.

Replace.

Defective ECM.

Replace.

Defective STP sensor or STVA.

Replace.

Defective GP switch.

Replace.

Engine lacks power 
(Defective control circuit 
or sensor)

Low fuel pressure.

Repair or replace.

Defective TP sensor.

Replace.

Defective IAT sensor.

Replace.

Defective CKP sensor.

Replace.

Defective GP switch.

Replace.

Defective IAP sensor.

Replace.

Defective ECM.

Replace.

Defective STP sensor or STVA.

Replace.

Imbalanced throttle valve 
synchronization.

Adjust.

TP sensor out of adjustment.

Adjust.

Summary of Contents for SFV650






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SFV650

Dynojet Power Commander III 718-411 Installation Instructions preview
Power Commander III 718-411
Brand: Dynojet Pages: 3
KTM 50 SX 2015 Setup Instructions preview
50 SX 2015
Brand: KTM Pages: 13
hepco & becker 5034566 00 01 Quick Start Manual preview
5034566 00 01
Brand: hepco & becker Pages: 3
Sundstrom SR 591 Instructions For Use Manual preview
SR 591
Brand: Sundstrom Pages: 68
hepco & becker 6304553 00 05 Mounting Instructions preview
6304553 00 05
Brand: hepco & becker Pages: 2
hepco & becker 5049515 00 05 Quick Start Manual preview
5049515 00 05
Brand: hepco & becker Pages: 3
GAS GAS 2007 PAMPERA 125 Manual preview
2007 PAMPERA 125
Brand: GAS GAS Pages: 58
MSW MSW-MC25L1 User Manual preview
MSW-MC25L1
Brand: MSW Pages: 11
Buell N1050.1AK Instruction Sheet preview
N1050.1AK
Brand: Buell Pages: 9
VESPA PX 125 Manual preview
PX 125
Brand: VESPA Pages: 64
Can-Am SPYDER RT 2022 Operator'S Manual preview
SPYDER RT 2022
Brand: Can-Am Pages: 204
Malaguti MADISON 300 2018 User Manual preview
MADISON 300 2018
Brand: Malaguti Pages: 120
Beta 400 RS 2014 Setup Manual preview
400 RS 2014
Brand: Beta Pages: 5
Beta 250-300 RR Setup Instructions preview
250-300 RR
Brand: Beta Pages: 5
hepco & becker 6707597 00 01 Mounting Instructions preview
6707597 00 01
Brand: hepco & becker Pages: 3
Rider 6 Riders User Manual preview
6 Riders
Brand: Rider Pages: 15
Royal Enfield Hunter 350 Owner'S Manual preview
Hunter 350
Brand: Royal Enfield Pages: 108
ORTILEB KSFB 26/100 Technical Documentation Manual preview
KSFB 26/100
Brand: ORTILEB Pages: 16

Brands by name

Popular brands

Load more brands