Suzuki SFV650 Service Manual Download Page 292

Page: 292 / 573

1E-13 Engine Lubrication System:

• Install the oil pump driven gear (4) and snap ring (5).

CAUTION

Never reuse a snap ring.

Special tool

: 09900–06107 (Snap ring pliers)

• Reinstall the clutch. Refer to “Clutch Installation in

Section 5C (Page 5C-9)”.

Oil Pump Inspection

B944H11506012

Inspect the oil pump in the following procedures:

1) Remove the oil pump. Refer to “Oil Pump Removal

and Installation (Page 1E-12)”.

2) Rotate the oil pump by hand and check that it moves

smoothly. If it does not move smoothly, replace the
oil pump assembly.

CAUTION

Do not attempt to disassemble the oil pump
assembly.
The oil pump is available only as an
assembly.

3) Install the oil pump. Refer to “Oil Pump Removal and

Installation (Page 1E-12)”.

Oil Pipe Removal and Installation

B944H11506014

Removal

1) Drain engine oil. Refer to “Engine Oil and Filter

Replacement in Section 0B (Page 0B-10)”.

2) Remove the clutch. Refer to “Clutch Removal in

Section 5C (Page 5C-7)”.

3) Remove the oil pipe stopper (1) by removing its

screw (2).

4) Remove the oil pipe (3).

Installation

Installation is in reverse order of removal.
Pay attention to the following points:
• Install the oil pipe (1).

I944H1150035-02

I944H1150036-01

I944H1150037-02

I944H1150038-02

I944H1150039-01

Summary of Contents for SFV650






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SFV650

Reviews:

Related manuals for SFV650

Brands by name

Popular brands

Suzuki SFV650, Service Manual

Search results

Summary of Contents for SFV650

Reviews:

Related manuals for SFV650

Brands by name

Popular brands