Suzuki SFV650 Service Manual Download Page 428

Page: 428 / 573

3A-6 Drive Chain / Drive Train / Drive Shaft:

Wheel Damper

Inspect the dampers for wear and damage. Replace the
damper if there is anything unusual.

Drive Chain

Refer to “Drive Chain Inspection and Adjustment in
Section 0B (Page 0B-15)”.

Sprocket Mounting Drum Dust Seal / Bearing
Removal and Installation

B944H13106005

Removal

1) Remove the rear wheel assembly. Refer to “Rear

Wheel Assembly Removal and Installation in Section
2D (Page 2D-11)”.

2) Remove the rear sprocket mounting drum assembly

from the rear wheel. Refer to “Rear Wheel Dust Seal
/ Bearing Removal and Installation in Section 2D
(Page 2D-13)”.

3) Remove the retainer (1).

4) Remove the sprocket mounting drum dust seal (2)

using the special tool.

Special tool

(A): 09913–50121 (Oil seal remover)

5) Remove the sprocket mounting drum bearing using

the special tool.

Special tool

(B): 09913–70210 (Bearing installer set)

Installation

CAUTION

The removed dust seal and bearing must be
replaced with new ones.

1) Apply grease to the bearing before installing.

: Grease 99000–25010 (SUZUKI SUPER

GREASE A or equivalent)

I944H1310019-01

I944H1310020-01

(A)

I944H1310021-01

(B)

I944H1310022-01

I649G1310020-02

Summary of Contents for SFV650






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SFV650

Reviews:

Related manuals for SFV650

Brands by name

Popular brands

Suzuki SFV650, Service Manual

Search results

Summary of Contents for SFV650

Reviews:

Related manuals for SFV650

Brands by name

Popular brands