Sony DCR-PC115 Service Manual Download Page 190

Page: 190 / 207

6-2

DCR-PC115/PC115E/PC120BT/PC120E

6-1-2. CABINET (L) SECTION

4-974-725-01 SCREW (M1.7), LOCK ACE, P2

X-3951-891-1 GRIP ASSY, HOLD

3-969-387-01 FOOT, RUBBER

3-070-419-01 COVER (G), JACK

3-062-141-01 BELT, GRIP

3-070-416-01 BRACKET, BELT

X-3951-954-1 CABINET (G) ASSY

X-3951-901-2 COVER (L) ASSY, JACK

X-3951-956-1 PLATE (L) ASSY, ORNAMENTAL

3-070-404-11 CABINET (L) (PC115/PC120BT)

3-070-404-21 CABINET (L) (PC115E/PC120E)

3-914-366-01 SCREW (DIA. 1.7X4), PRECISION

1-476-871-11 SWITCH BLOCK, CONTROL (FK-1850)

X-3951-896-1 FRAME ASSY, JACK

Ref. No.

Part No.

Description

Remarks

Ref. No.

Part No.

Description

Remarks

3-070-467-01 SHEET (N), MUFFLE

X-3951-955-1 CABINET (REAR) ASSY (PC120BT/PC120E)

X-3951-958-1 CABINET (REAR) ASSY (PC115/PC115E)

3-062-128-01 SPRING, COMPRESSION

3-070-431-01 LOCK, BATTERY

1-476-870-11 SWITCH BLOCK, CONTROL (PS-1850)

A-7074-971-A KY-060 (N) BOARD, COMPLETE

(PC120BT/PC120E)

A-7078-010-A KY-060 BOARD, COMPLETE (PC115/PC115E)

X-3951-889-1 FRAME ASSY, G

3-973-497-91 SCREW (M1.7), 0-NO. +P 2

3-071-508-01 SHEET (L)

SP901

1-529-857-11 SPEAKER (1.6 CM)

SP901

not
supplied

(Note)

: BT001 (Lithium battery) Control switch block (FK-1850) on the mount position. (See page 4-80)

The +P2 (0-No.) screws (M1.7

2.5) are MEC-processed. If the screws that are once removed,

are re-used, the screws may be loosened.
When re-assembling the mechanism, use the new +P2 (0-No.) screws (M1.7

2.5).

Note:

Summary of Contents for DCR-PC115
















































































































































































































Search results

Summary of Contents for DCR-PC115

Reviews:

Sony DCR-PC115, Service Manual, Page: 190 / 207

Search results

Summary of Contents for DCR-PC115

Reviews: