Sony DCR-PC115 Service Manual Download Page 161

Page: 161 / 207

5-38

DCR-PC115/PC115E/PC120BT/PC120E

4. Contrast Adjustment (VM-027 board)

Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).

Mode

Camera

Subject

Arbitrary

Measurement Point

of CN008 of VC-270 board

(EVF VG)

Measuring Instrument

Oscilloscope

Adjustment Page

Adjustment Address

Specified Value

A = 2.45 ± 0.05V

Adjusting method:

Order Page Address Data

Procedure

Set the data.

Change the data and set the voltage
(A) between the 3 steps peak and
pedestal to the specified value.
(The data should be “00” to “7F”.)

Press PAUSE button.

Set the data.

5. White Balance Adjustment (VM-027 board)

Correct the white balance.
If deviated, the reproduction of the EVF screen may degenerate.

Mode

Camera

Subject

Arbitrary

Measurement Point

Check on EVF screen

Measuring Instrument

Adjustment Page

Adjustment Address

97, 98

Specified Value

The EVF screen should not be colored.

Note1:

Check the white balance only when replacing the following parts.
If necessary, adjust them.

1. LCD panel
2. Light induction plate
3. IC1802
4. D3701, D3702

Note2:

Use the AC power adaptor.

Adjusting method:

Order Page Address Data

Procedure

Set the data.

Set the data, and press PAUSE
button.

Check that the EVF screen is not
colored. If not colored, proceed to
step 10.

Change the data so that the EVF
screen is not colored.

Press PAUSE button.

Change the data so that the EVF
screen is not colored.

Press PAUSE button.

If the EVF screen is colored, repeat
steps 5 to 9.

Set the data.

Fig. 5-1-20.

3 steps peak

Pedestal

Summary of Contents for DCR-PC115
















































































































































































































Search results

Summary of Contents for DCR-PC115

Reviews:

Sony DCR-PC115, Service Manual, Page: 161 / 207

Search results

Summary of Contents for DCR-PC115

Reviews: