Somati system FSTronic IRC-FI Manual Download Page 6 | Manualshive

Page: 6 / 44

background image

www.somati-system.cz

6

6.

External battery (voluntarily accessory), recommended only
original accumulators - 24V (2x12V) with fusing

7.

Installation of the battery fuse. Fuse is delivered together with control unit,

but is not inserted in connector. Is fixed on the door of control unit. Fuse

type tubular fuse 10x38 gG32a.

Do not connect any external controls or any other devices before setting

the end switches – it can cause automatic ﬆart, which is not reﬆricted
due to the unset end switches.

Steps for connection to power:
Connect power supply and only then connect batteries (see point 7.)
Steps for disconnecting power:
First disconnect batteries and then disconnect power supply.

6.

6.

6.

7.

7.

!

«
...
4
5
6
7
8
...
»

Summary of Contents for FSTronic IRC-FI













































Reviews:

No comments

Related manuals for FSTronic IRC-FI

ControlMaster CM15

Brand: ABB Pages: 28

Brand: FAAC Pages: 12

Brand: Fairchild Pages: 2

Brand: Fagor Pages: 103

Brand: Accel Pages: 8

Brand: B&R Industries Pages: 89

BT300 BurnerTronic

Brand: Lamtec Pages: 48

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: K&G GROEP Pages: 27

Brand: CAME Pages: 2

Brand: CalAmp Pages: 13

Brand: ZKTeco Pages: 13

Brand: UniPi Technology Pages: 4

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

Brand: Hunter Pages: 2

Brand: Tektronix Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands