manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 88 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 88

Connection 

 

7.3 Connection of Siemens SENTRON switching devices 

 

3KC ATC6300 transfer control device 

86

 

Manual, 03/2018, L1V30535632002A-01 

7.3.3.1

 

Typical operating times of the Siemens SENTRON switching devices in accordance 

with IEC 60947-6-1 (IEC only) 

The following typical operating times can be achieved with the ATC and Siemens circuit 

breakers in accordance with IEC 60947-6-1. Take the operating times for the 3KC3 and 

3KC4 remotely operated transfer switching equipment from the corresponding manual or 

catalog. 

 

 

Note 
The tables below contain typical operating values. Check the operating times of the 

respective total installation under real conditions. 

 

Operating times of the 3VA 

 

 

Unit 

2x  

3VA1 160A  

+ 2x MO 

2x  

3VA1 250A 

+ 2x MO 

2x 

3VA2 100A  

+ 2x MO 

2x  

3VA2 100A  

+ 2x SEO 

2x  

3VA2 160A  

+ 2x MO 

Contact transfer time, 

off-time* 

ms 

900 

900 

1100 

180 

1100 

Operating time I-O, 

II-O 

ms 

800 

800 

1000 

80 

1000 

Transfer time I-O-II, 

II-O-I (for min para-

meter)* 

ms  

1700 

1700 

2100 

260 

2100 

 * Comprises the minimum delay time from Line I to Line II of 100 ms (see parameter P05.03) in the OFF position 

 

 

 

Unit 

2x  

3VA2 160A  

+ 2x SEO 

2x  

3VA2 250A  

+ 2x MO 

2x  

3VA2 250A  

+ 2x SEO 

2x  

3VA2 400A  

+ 2x MO 

2x  

3VA2 630A  

+ 2x MO 

Contact transfer time, 

off-time* 

ms 

180 

1100 

180 

1800 

1800 

Operating time I-O, 

II-O 

ms 

80 

1000 

80 

1400 

1400 

Transfer time I-O-II, 

II-O-I (for min para-

meter)* 

ms  

260 

2100 

260 

3200 

3200 

 * Comprises the minimum delay time from Line I to Line II of 100 ms (see parameter P05.03) in the OFF position 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments