Siemens SENTRON ATC6300 Manual Download Page 73

Page: 73 / 210

Connection

7.2 Connection of the power supply

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

7.2.1

Implementation of the dual power supply by means of dual network connection

3KC9625-1 (for IEC applications only)

The ATC6300 can be supplied from two 230 V AC power supply systems with the dual

network connection (3KC9625-1).
Properties of the dual network connection

●

Active as from 200 V AC

●

Maximum voltage: 288 V AC, frequency: 45 ... 65 Hz

●

Internal fuse: Each input is protected with a fuse up to 3.15 A.

Mounting the dual network connection
The dual network connection must be mounted on a standard mounting rail.
1.

Place the dual network connection (3KC9625-1) with plug connection from above onto

the standard mounting rail.

Align the clip assembly with a screwdriver as shown in the figure.

Align the plug connection on the underside.

Carefully push the device back until the plug connection audibly engages on the

underside

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 73 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: