Siemens SENTRON ATC6300 Manual Download Page 27

Page: 27 / 210

Product description

4.5 Display pages of the ATC6300

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

The submenu L-L Voltage shows the voltage between the phases.
The menu shows

●

the voltages currently being measured

●

the frequency of both lines currently being measured

●

the current operating mode

This view is not available in single-phase supplies.

L-N Voltage

The submenu L-N Voltage shows the voltage between the phase and the neutral conductor.
The menu shows

●

the voltages currently being measured

●

the frequency of both lines currently being measured

●

the current operating mode

Control Thresholds

①

Maximum control threshold for Voltage (L-L) Line 2

②

Minimum control threshold for Frequency Line 2

③

Maximum control threshold for Frequency Line 1

④

Minimum control threshold for Voltage (L-L) Line 1

The Control Thresholds submenu shows the maximum and minimum threshold values for

triggering the transfer.

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 27 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: