Siemens SENTRON ATC6300 Manual Download Page 44

Page: 44 / 210

Functions

5.1 Basic functions

3KC ATC6300 transfer control device

Manual, 03/2018, L1V30535632002A-01

5.1.4.1

Enabling additional resources

The expansion modules provide additional resources that can be used via the corresponding

setup menus.

Note
Availability during physical absence of modules
The setup menus for the expansions are also available if the modules are not physically

present, i.e. the inputs 6-14 on the device can be parameterized, even though no module is

inserted and these inputs are therefore not available.

As it is possible to add several modules of the same type (for example, two communication

interfaces), several of the corresponding setup menus are available and are identified by

consecutive numbering.
The table below shows how many modules of each type can be installed simultaneously and

in which slots they may be used. There must be no more than two modules.

Module type

Article number Function

Maximum num-

ber that can be

inserted

Communica-

tion

3KC9000-

8TL74

RS485 (MODBUS RTU)

3KC9000-

8TL75

Ethernet (MODBUS TCP)

Digital inputs

and outputs

3KC9000-

8TL60

4 digital inputs

3KC9000-

8TL61

4 digital outputs, SSR (4 NO contacts)

3KC9000-

8TL62

2 digital inputs and 2 digital outputs, SSR (2 NO

contacts)

3KC9000-

8TL63

2 digital relay outputs (2 changeover contacts)

3KC9000-

8TL64

2 digital inputs and 2 relay outputs (2 NO con-

tacts)

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 44 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: