manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 138 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 138

Parameterization 

 

9.3 Parameters 

 

3KC ATC6300 transfer control device 

136

 

Manual, 03/2018, L1V30535632002A-01 

9.3.9

 

P09 - Automatic test 

 

 

P09 – 
Automatic 

test 

Designation on ATC 

display 

Description 

Unit 

Default   Range  

P09.01  

Auto test enable 

Enabling the automatic test  
– Enables the execution of the periodic test. 

This parameter can be modified directly from 

the front operator panel, without invoking the 

setup procedure. Its current status is displayed 

on the corresponding display page, see chapter 

Automatic test (Page 51). 

 

OFF  

OFF / ON  

P09.02  

Auto test period 

Interval between performing the TESTS  
– Interval between two periodic tests. If the test 

is not enabled on the day it becomes due, the 

period is extended to the next enabled day. 

 

7  

1gg-60gg 

P09.03  

Auto Test Monday 

TEST execution on Monday  
- Enables the performance of the automatic test 

on the individual days of the week.  
OFF means that the test is not performed on 

that day of the week. 

 

ON  

OFF / ON  

P09.04  

Auto Test Tuesday  TEST execution on Tuesday 

- see Parameter 09.03  

 

ON  

OFF / ON  

P09.05  

Auto Test Wednes-

day 

TEST execution on Wednesday  
- see Parameter 09.03  

 

ON  

OFF / ON  

P09.06  

Auto Test Thursday  TEST execution on Thursday  

- see Parameter 09.03  

 

ON  

OFF / ON  

P09.07  

Auto Test Friday 

TEST execution on Friday  
- see Parameter 09.03  

 

ON  

OFF / ON  

P09.08  

Auto Test Saturday  TEST execution on Saturday  

- see Parameter 09.03  

 

ON  

OFF / ON  

P09.09  

Auto Test Sunday 

TEST execution on Sunday  
- see Parameter 09.03  

 

ON  

OFF / ON  

P09.10  

Auto test hour 

Hour of TEST start  
- Specifies the hours and the minutes for the 

start of the periodic test.  

h  

12  

00-23  

P09.11  

Auto test minute 

Minutes of TEST start  
- see Parameter 09.11 

min  

00  

00-59  

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments