manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 126 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 126

Parameterization 

 

9.3 Parameters 

 

3KC ATC6300 transfer control device 

124

 

Manual, 03/2018, L1V30535632002A-01 

9.3.4

 

P04 - Battery 

 

 

 

Note 
Use of DC power supply 
The following parameters are necessary only if you are using a DC power supply (see 

chapter Connecting the power supply (Page 70)). 

 
 

 

P04 
Battery 

Designation on ATC 

display 

Description 

Unit 

Default 

Range 

P04.01 

Battery voltage 

Nominal voltage of the DC supply 
– This parameter defines the voltage of the 

additional DC supply of the ATC6300. 
Note: If this parameter is set to OFF, all alarms 

regarding the DC supply, as well as the indica-

tor for the battery voltage, are disabled.  

V 

AUTO 

AUTO 
12 
24 
OFF 

P04.02 

Max voltage limit 

Maximum voltage limit of the DC supply 
– This defines the upper limit threshold for the 

battery voltage.  

% 

130 

110 - 140 

P04.03 

Min voltage limit 

Minimum voltage limit of the DC supply 
–  This defines the lower limit threshold for the 

battery voltage.  

% 

75 

60 - 130 

P04.04 

Min / Max volt. delay  Minimum / maximum voltage delay of the DC 

supply 
– This parameter defines the delay for the min-

imum / maximum DC supply voltage. If the 

voltage exceeds the upper or lower limits from 

P04.02 and P04.03 for the period defined by 

this parameter, the corresponding alarms are 

triggered.  

s 

10 

0 - 120 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments