manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 78 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 78

Connection 

 

7.3 Connection of Siemens SENTRON switching devices 

 

3KC ATC6300 transfer control device 

76

 

Manual, 03/2018, L1V30535632002A-01 

Generator/generator transfer 

The output Control Generator 2 must then be programmed in such a way that the generator 

is started when the ATC6300 is de-energized.  

 

Connection 

Parameter 

Output type 

Setting 

OUT (3) 22 - 23 

P11.03.01 

NOR 

Control Generator 2 

OUT (2) 11 - 12 

P11.02.01 

REV 

Control Generator 1 

7.3

 

Connection of Siemens SENTRON switching devices 

The connection of the Siemens switching devices is shown below  

7.3.1

 

Accessories for switching devices 

The following accessories are necessary for the Siemens switching devices: 

 

Circuit breaker 

Accessories required 

3KC 

Emergency pushbutton 

3VA 

Auxiliary switch (interlock) 
Auxiliary switch (status) 
Alarm auxiliary switch (trip) 
Motor operator 

3VL 

Auxiliary switch, normally open (NO) (interlock) 
Auxiliary switch, normally closed (NC) (status) 
Alarm auxiliary switch (trip) 
Motor operator 

3WL 

Auxiliary switch (interlock) 
Auxiliary switch (status) 
Tripped signaling switch (trip) 
Auxiliary trip unit (shunt release) F1 
Closing solenoid Y1 
Motor operator 

3WT 

Auxiliary switch (interlock) 
Auxiliary switch (status) 
Tripped signaling switch (trip) 
Auxiliary trip unit (shunt release) F1 
Closing solenoid Y1 
Motor operator 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments