Siemens SENTRON ATC6300 Manual Download Page 46

Page: 46 / 210

Functions

5.1 Basic functions

3KC ATC6300 transfer control device

Manual, 03/2018, L1V30535632002A-01

5.1.4.3

Behavior of the ATC6300 after inserting a module

As soon as the power supply is connected to the ATC6300, it automatically detects a new

expansion module.
If the system configuration deviates from the last configuration stored (if, for example, a

module has been inserted or removed), the ATC6300 prompts the user to confirm the new

configuration.
After confirmation the ATC6300 will restart. After this, the module can be parameterized.
If the change is not accepted a reference is made to the change every time it starts up.

Note
Addressing the modules
When subsequently removing an expansion module, attention must be paid to the

addressing of the module.

The following message is displayed if a new configuration has been detected:

The current system configuration is displayed on the corresponding display page (Expansion

Modules), stating the number, type and status of the connected modules:

●

The I/O numbering is shown under each module.

●

The status (activated / deactivated) of the I/O and of the communication channels is

indicated by the message displayed in negative.

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 46 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: