manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 163 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 163

 

MODBUS communication 

 

11.6 Data library 

3KC ATC6300 transfer control device 
Manual, 03/2018, L1V30535632002A-01 

161

 

④

 The 16 bits of the status Voltage for Line 1 and Line 2 for the address 2074h or 2176h 

have the following meaning:  

 

Bit 

Status of the line 

0 

Parameter of the line within the limit thresholds 

1 

Parameter of the line within the limit thre delay 

2 

Voltage within the limit thresholds 

3 

Voltage OK 

4 

Frequency within the limit thresholds 

5 

Frequency OK 

6 

Voltage below the lower threshold 

7 

Voltage above the upper threshold 

8 

Voltage unbalance 

9 

Phase failure 

10 

Frequency below the lower threshold 

11 

Frequency above the upper threshold 

12 

Incorrect phase sequence 

13 

All parameters of the Line OK 

14-15 

Not used 

⑤

 The 16 bits of the status of Breakers for Line 1 and Line 2 for the address 2075h or 

2177h have the following meaning:  

 

Bit 

Status of the breaker 

0 

Breaker closed 

1 

Trip alarm 

2 

Not used 

3 

Command status (1= close) 

4 

Output command close 

5 

Output command open 

6-15 

Not used 

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments