manualshive.com logo in svg

Siemens SENTRON ATC6300, Manual, Page: 133 / 210

Share
Download
Siemens SENTRON ATC6300 Manual Download Page 133

 

Parameterization 

 

9.3 Parameters 

3KC ATC6300 transfer control device 
Manual, 03/2018, L1V30535632002A-01 

131

 

P06 Pa-

rameter 

Line 1 

Designation on ATC 

display 

Description 

Unit 

Default 

Range 

P06.08 

Pres.del. Line 2 OK  Presence delay (when Line 2 source available) 

– Is used if the load on Line 2 can be connect-

ed.  
Normally this time is longer than P6.07, as the 

load is being energized, and it is possible to 

wait longer before considering voltage steadily 

restored.  

s 

60 

1-6000 

P06.09 

Phase failure thresh  Threshold limit for phase failure 

– Voltage threshold below which a phase loss 

intervention occurs, 
usually quicker than the drop. The delay for the 

phase failure is specified by P06.10.  

% 

70 

60 - 80 
OFF 

P06.10 

Phase failure delay  Delay time for the phase failure threshold limit 

- see Parameter 06.09 

s 

0.1 

0.1 s-30 s 

P06.11 

Max. asymmetry 

limit 

Maximum limit for asymmetry of the phases 
- P06.11 specifies the upper threshold for 

phase asymmetry referred to nominal voltage, 

and P06.12 defines the related intervention 

delay.  
This measurement can be disabled by setting 

P06.11 to OFF  

% 

15 

1 % - 20 % 
OFF 

P06.12 

Max asymmetry 

delay 

Delay time for maximum asymmetry of the 

phases 
- see Parameter 06.11 

s 

5 

0.1-900 

P06.13 

Max frequency limit  Limit for the maximum frequency 

- (can be disabled).  

% 

105 

100-120 
OFF 

P06.14 

Max frequency 

delay 

Delay time for the maximum frequency 

s 

3 

0-600 

P06.15 

Min frequency limit  Limit threshold for minimum frequency (can be 

disabled) 
- Maximum frequency intervention delay.  

% 

95 

OFF 
80-100 

P06.16  

Min frequency delay  Delay time for minimum frequency  

s  

5  

0-600  

P06.17  

Line cont. OFF 

mode 

Setting of the voltage measurement in the OFF 

mode 
 

 

OFF  

OFF

1)

 

ON

2)

 

OFF+GLOB

3)

 

ON+GLOB

4)

  

P06.18  

Line cont. MAN 

mode 

Line cont. MAN mode 
- As for Parameter 06.17, but referred to the 

MANUAL mode 

 

OFF  

OFF  
ON  
OFF+GLOB  
ON+GLOB  

Summary of Contents for SENTRON ATC6300



















































































































































































































Reviews:

No comments