Siemens SENTRON ATC6300 Manual Download Page 129

Page: 129 / 210

Parameterization

9.3 Parameters

3KC ATC6300 transfer control device
Manual, 03/2018, L1V30535632002A-01

127

P05
Changeo-

ver

Designation on ATC

display

Description

Unit

Default

Range

P05.14

EJP start delay

EJP start delay
– Delay between the EJP start signal and the

actual start signal at the generator.

min

0-240

P05.15

EJP changeover

delay

EJP changeover delay
– Delay in changing over the load from the

priority to the secondary line in the EJP and

SCR mode.

min

0-240

P05.16

Changeover lock

Locking of the EJP return changeover
– If set to ON, the load in the modes EJP, EJP-

T and SCR is not switched back to the priority

line when a fault occurs in the generator, but

only when the signals at the EJP inputs enable

the changeover.

OFF/ON

P05.17

Switch aft. FB alarm Changeover if closing is incomplete

– When this parameter is enabled and the

switching device does not close successfully

(no feedback on presence of opening com-

mand), not only the corresponding feedback

alarm (A03 or A04) is triggered, but changeover

to the secondary line is also controlled.
OFF = Function disabled
1 = Check Line 1
2 = Check Line 2
1+2 = Check both lines.

OFF

OFF
1
2
1+2

P05.18

Min. coil pulse dur. Duration of the opening pulse of the undervolt-

age release for the opening of the switching

devices
– If an additional undervoltage release is used,

this parameter defines how long the output is

opened with the undervoltage release function

Line 1 or 2 (see chapter Table of functions of

the digital outputs (Page 112))

1.0

0.1 … 10.0

P05.19

Delay after min. coil Delay between opening pulse of the undervolt-

age release and spring reload command
– This parameter defines after which time (after

parameter P05.18 has elapsed) an opening

command to load the springs is sent to the

switching device.

0.2

0.1 ... 10.0

Summary of Contents for SENTRON ATC6300



















































































































































































































Search results

Summary of Contents for SENTRON ATC6300

Reviews:

Siemens SENTRON ATC6300, Manual, Page: 129 / 210

Search results

Summary of Contents for SENTRON ATC6300

Reviews: